So, you want to know more about heating and air condition service in Mt. Pleasant Area, SC? Sounds too complicated? Do you find the terms confusing? We’ll simplify all that is involved for you in this article. If it still confuses you, then please do reach out to a company that offers heating and air condition service in Mt. Pleasant Area.
The entire operation summed up
A typical heating and air condition service in Mt. Pleasant Area makes use of forced air heating, powered by gas. The unit pulls in all cold air from the surroundings, and then transfers it to a metallic box, referred as the heat exchanger. The collected air is then heated, and pushed out to a duct network by a blower fan. This duct network is deployed throughout your house, and ejects the heated air into all your rooms.
A furnace is used for producing heat. For old units, its efficiency is around 60%, but with new models, you can enjoy values as high as 96%. A company that offers heating and air condition service in Mt. Pleasant Area can guide you more on furnace’s efficiency values.
And how is a single unit heating or cooling my whole house
The ductwork network as we mentioned earlier. This network is distributed throughout our house. Your chosen heating and air condition service in Mt. Pleasant Area can install this for you. One Call Heating charges quite reasonably for this service.
Anyway, a ductwork is a tubing system that blows out hot air and transfers it to every room in your house. It also takes in the cold air in the room, and ejects it into the outside environment.
Furnace types – lets quickly compare them
A furnace used with heating and air condition service in Mt. Pleasant Area can be broken down into three main types: single stage, two stages, and modulating. Each of these three types goes through an on-off cycle that is dependent on the value set on your thermostat. Your home temperature will always be in between these two points.
This furnace is pretty much like a stove, with only one fixed value. You can either turn this furnace on or off; there is no in between. So, is this good? Not really because the temperature oscillates way too much and may cause inefficiency.
Just as the name suggests, a two stage furnace has two settings: you can set the furnace at a high temperature and at a low temperature in addition to turning it on and off. Thus, air temperature is varied and the heat does drop down, but not too much; the temperature is always maintained within an acceptable range.
Obviously, this makes the two stage thermostat better than a single stage thermostat. The temperature is varied which reduces the burden on the air conditioning unit, and so it consumes less energy.
Modulating furnace is exactly those advanced stove range that you have in your kitchen. Just as you adjust the flames by turning the knob, you adjust the temperature by turning the knob on the AC. The unit tries to maintain a constant temperature, which increases comfort and improves efficiency. From a practical perspective, however, modulating furnaces are a kind of new technology, and not really proven. But, a company that offers heating and air condition service in Mt. Pleasant Area can guide you more. Do talk to them, before considering this kind of furnace.
Variable speed blower
This kind of furnace adjusts the speed of fan incrementally to allow for more precise control over the air flow. These kinds of furnaces are more efficient than a single stage and two stage furnace, and increase comfort level. Plus, they consume less electricity because they convert AC into DC prior to operation.
We talked about a furnace, but what about cooling? How does the AC work?
The functioning of an air conditioning unit is like a refrigerator. A refrigerant is passed through a metal coils network. This is a substance that can convert from a liquid into a gaseous state at low temperatures. Warm air is passed over the coil network. The refrigerant absorbs the emitting heat, and converts into the gas, cooling down air in the process. The cool air is then passed to the duct network, which blows it through the house.
The refrigerant, still in its gaseous form, is passed to the compressor, where it is subjected to pressure, converting back into a liquid. The process releases heat which is ejected out of the system into the surroundings.
Capacity, reliability and efficiency are important specifications for an AC unit. Discuss this in detail with a company that offers heating and air condition service in Mt. Pleasant Area.
We’ve covered quite a lot; let’s look at efficiency now
Over time, the efficiency of cooling units has considerably improved. What were considered to be the standard ratings some years ago are now below the minimum accepted values. Specified in SEER, the minimum efficiency of any air conditioning unit is 13 SEER.
If you are using a unit that has an efficiency value greater than 14.5, then you can expect some rebates from the utility providers. Obviously, the greater the SEER values, the more efficiency you enjoy and the lower are your bills. However, you also pay a bigger price for it. One call Heating, a heating and air condition service in Mt. Pleasant Area, can guide you more about affordable brands.
Generally, you don’t get substantial energy savings, when compared to the costs involved, if you go for values greater than 16.
Needless to say, regular maintenance is the cue to efficient operation, so do get these scheduled through a reliable heating and air condition service in Mt. Pleasant Area.